- Dac digital to analog audio converter full#
- Dac digital to analog audio converter series#
- Dac digital to analog audio converter free#
Specificationsĭetailed specifications and performance plots are available in the downloadable manual.When talking about signals, they can be broadly classified into analog signals and digital signals. The performance of the HPA2™ remains consistent even when two headphones are being driven simultaneously. The DAC1 has two 1/4" headphone jacks on the front panel.
Dac digital to analog audio converter full#
The HPA2™ maintains less than 0.0003% THD+N under full load. It will deliver the full rated performance of the DAC1 to the headphones. The HPA2™ is arguably the ultimate reference headphone power amplifier. The DAC1 features the HPA2™ - Benchmark's signature high-current, 0-Ohm headphone power amplifier. Two units can be mounted side-by-side in a 1-RU tray. Add a Rack-Mount KitĪll Benchmark DAC1, DAC1, ADC1, and MPA1 products are housed in a 1/2-wide 1 RU chassis. Our optical cables are manufactured in Canada. Benchmark cablesare designed for durability and transparency, and most are manufactured in the USA. Add Benchmark Cables to Complete You New Systemīenchmark offers a no-nonsense selection of very high-quality cables. The bottom line is this: Benchmark converters will consistently and faithfully deliver truthful audio with no jitter-induced artifacts, no matter what variables are present. Any signal that can be decoded by the AES/EBU receivers will be reproduced without the addition of any measurable jitter artifacts. Using state-of-the-art Audio Precision testing equipment, no jitter-induced artifacts can be detected with the DAC1.
This clock-recovery topology outperforms even the most well-designed two-stage PLL designs. With the UltraLock™ clock-recovery system, the digital-to-analog conversion-clock in the DAC1 is totally isolated from the clock of the digital audio input. Jitter is NOT a problem for the DAC1, which achieves jitter immunity by utilizing Benchmark's proprietary UltraLock™ clock-recovery system. Many modern (and expensive) converters suffer from severe jitter-induced distortion. The result of these misfires is a non-musical, digital distortion. Jitter is a type of clock error that, if not properly addressed, can cause the D-to-A to misfire. Jitter presents a major problem to most D-to-A converters. Jitter-Immune UltraLock™ĭigital interconnect cables, electro-magnetic interference, and many other variables introduce jitter into the digital audio. This important feature maximizes the signal to noise ratio of the entire playback system. These attenuators can be set in 10 dB steps to optimize the gain-staging between the DAC and the power amplifier.
The XLR outputs are equipped with Benchmark's exclusive low-impedance passive output attenuators. Direct Interface to Power AmplifiersĪll Benchmark DAC1 and DAC2 converters are designed to directly interface with power amplifiers and powered monitors. In the "Calibrated" setting, the rear-panel outputs are controlled by multi-turn calibration pots. A rear-panel switch selects "Variable" or "Calibrated" output levels.
It can also be used to control the output level of the balanced XLR and unbalanced RCA analog outputs. The front-panel gain control sets the output level of the headphone jacks. The power supply is sized to supply the demands of the HPA2™ headphone power amplifier when driving two sets of headphones. The large internal power supply supports all international voltages and has generous margins for over and under voltage conditions. Audiophiles have also discovered the smooth and detailed sound of the DAC1, and it has become a centerpiece in may home listening rooms.
Dac digital to analog audio converter free#
The DAC1 is free from digital artifacts and its analog sound eliminates the fatigue that is caused by many digital devices. Audio engineers rely of the accurate, uncolored, and precise sound of Benchmark DAC1 converters. An Industry Standardīenchmark's award-winning DAC1 has become a standard in the finest recording studios and mastering rooms. Made in the USAīenchmark products are designed and manufactured in the USA. A compact and rugged enclosure makes the DAC1 an excellent choice for location recording, broadcast facilities, and mobile trucks. The DAC1 is designed for maximum transparency and is well suited for critical playback in studio control rooms and in mastering rooms. The DAC1 is a reference-quality, 2-channel 192-kHz 24-bit audio digital-to-analog converter featuring Benchmark’s UltraLock™ technology. Buy a Factory Refurbished DAC1 exclusively on our website!
Dac digital to analog audio converter series#
This model has been replaced by the DAC2 Series D/A converters. The DAC2 series has higher performance and many more features.
0 kommentar(er)
